LOGIN
Abhi Verma
33
Community Expert
ROBOToTHON 2017 Mentor, Electronics Engineer
 · DelhiIndia
Share
Report
Get Link
IDEA

NRF multi-channel Remote

I was thinking to develop a low cost muti-channel remote along with a Rx having multi-functional outputs.
e.g. Remote Tx will have two joysticks modules on board, 6- Analog channels to interface custom hardware and sensors, 6 - digital switches.

Rx module can be configured to output PPM signals, or digital signals. along with 6 available PWM outputs as well. and any output can be mapped to any input at TX side.

What you guys think about this device and scope in market?
Ravi Pujar Steven Reubenstone Harsha Alva John Rodrigues Anton Voltchok

Contributions
Harsha Alva

Make what can not be bought is my Lifestyle .
Average flight remote unit costs over $150 and the hobbiests and the students can not afford it . even if you do not make
the fancy cover , does not matter at all , in the phaze 1 you can sell the Kit, fully programed to be used, people will make the cover them selves, as in bulk 3d printing will be very costly ,

4 likes 
Like
Award Contribution
Load 5 previous comments
Ravi Pujar
15
Mastermind
Embedded systems engineer, Founder @Valetron Systems, Blogger @www.raviyp.com
 · DharwadIndia
Share
Report
Get Link

We should plan on enclosure as well, Because people need to hold these in hands and operate. Or you can also be a OEM for other remote manufacturers too.

Like
1 like 
Award Contribution
Abhi Verma
33
Community Expert
ROBOToTHON 2017 Mentor, Electronics Engineer
 · DelhiIndia
Share
Report
Get Link

good idea Ravi. I’ll develop the boards and sell them as DIY modules. and if succeed than we can fit them in enclosures. I think this way we will have minimum risk and minimum investment.
your thoughts?

Contribution
Like
0 like 
Award Contribution
Ravi Pujar
15
Mastermind
Embedded systems engineer, Founder @Valetron Systems, Blogger @www.raviyp.com
 · DharwadIndia
Share
Report
Get Link

Yes, Get it working and later someone from community can make open source 3D enclosure design after you are done and everyone can 3D print the enclosure themselves after buying module

Like
1 like 
Award Contribution
Steven Reubenstone
34
Community Expert
Mechanical Engineer & Tinkerer of Things.
 · New YorkU.S.
Share
Report
Get Link

Nice

Like
0 like 
Award Contribution
Abhi Verma
33
Community Expert
ROBOToTHON 2017 Mentor, Electronics Engineer
 · DelhiIndia
Share
Report
Get Link

Thanks everyone. Once i have free time, I’ll complete this.

Like
2 likes 
Award Contribution
Abhi Verma
33
Community Expert
ROBOToTHON 2017 Mentor, Electronics Engineer
 · DelhiIndia
Share
Report
Get Link

This is JoyPad-NRF V1.0 . it has many features available on board.

  1. Joystick modules x 2
  2. Gyro/Accelrometer GY-521 - MPU6050 slot
  3. NRF2401+ Radio module (changeable to high range modules )
  4. OLED 128x64 display
  5. USB to TTL converter
  6. Arduino Nano compatible
  7. User can program custom firmware directly with Arduino IDE.
  8. Reverse polarity protection
  9. input power- 5v-10v

any other function i need to add?

Like
1 like 
Award Contribution
Leave a reply...
DISCOVER
CHAT
ALERTS
DISCUSSIONS
FEED
New Post
Facebook Share
Share Link
Help